Set the paper release lever to the single-sheet position. See About Your Printer's Default Settings.Ĭontinuous paper may be left in the printer. Set skip-over-perforation to off in the Default Setting mode. One-inch skip-over-perforation may be set. See About Your Printer's Default Settings. The printer's page length setting for the tractor may not match the size of the continuous paper you are using.Ĭheck Page length for tractor of the printer's default settings.
EPSON LX 300 PRINTER RIBBON SOFTWARE
The page length setting in your application may be incorrect.Ĭheck the page length set by your application software and adjust it if necessary. Page length does not match the length of the paper.
Your application software settings may be incorrect.Ĭheck the margin or top-of-form position setting in your application software. Printing starts too high or too low on the page, or the bottom part of one page is printed at the top of the next page. The print position is not what you expected
Your software may be overriding your control panel setting.Ĭheck the font setting in your application software. The font selected on the control panel does not print. The software may not be properly configured.Ĭheck that the software is correctly configured for your printer. The typestyles or characters you sent with your software did not print. Printed characters are not what you expected Reinstall the ribbon cartridge as described in Replacing the Ribbon Cartridge. Stop printing and contact your dealer to have the print head replaced.Įither there is too much slack in the ribbon or the ribbon has come loose. Replace the ribbon cartridge as described in Replacing the Ribbon Cartridge.ĭots are missing in printed characters or graphicsĪ line of dots is missing in the printout. Printed characters have parts missing at the bottom. (If an error occurs when you switch between single sheets and continuous paper, make sure the paper release lever is in the correct position.) If there is no jam, contact your dealer or a qualified service person. If the problem persists, check for a paper jam or ribbon jam. Turn off the printer and turn it on again. The beeper sounds five times and all the lights blink. If the printer still does not print correctly contact your dealer. Turn off the printer and check for a paper jam, a ribbon jam or other problems. The printer makes a strange noise, the beeper sounds five times, and the printer stops abruptly. The ribbon cartridge may not be installed properly. The printer sounds like it is printing, but nothing is printed. The Paper Out and Pause lights are on and the printer beeps three times. Then, click the Ports or Details tab and select the appropriate port.
When the icon of the printer you are using appears, right-click it and select Properties.
EPSON LX 300 PRINTER RIBBON WINDOWS
For Windows XP, click Start, Control Panel, then click Printers and Faxes. The printer port may not be set correctly.įor Windows 98, Me, 2000 or Windows NT 4.0, click Start, point to Settings, then click Printers. Make sure the cable meets both the printer and computer specifications. The interface cable may not match the specifications of the printer or computer.Ĭheck both ends of the interface cable. The software may not be installed properly.Ĭheck that the software is installed properly for your printer, as described in the Start Here. The PAUSE light is off but nothing is printed.
Do not reconnect the power cord to an electrical outlet. If the voltages do not match, unplug the printer and contact your dealer immediately. The voltage ratings of the printer and electrical outlet may not match.Ĭheck that the printer's voltage rating matches the voltage of your electrical outlet. The lights stay off even when the power is turned on again. The lights come on briefly and then go off. Plug another electrical device, such as a lamp, into the outlet to determine whether the outlet is operating properly. If the electrical outlet is controlled by an outside switch or automatic timer, use a different outlet. The lights on the control panel do not go on.Ĭheck that the power cord is properly plugged into the electrical outlet. The printer prints all the codes it receives in hexadecimal format. Next, hold down the Load/Eject and LF/FF buttons while you turn on the printer. To print a hex dump, turn off the printer. If you are an experienced user or a programmer, you can print a hexadecimal dump to isolate communication problems between the printer and computer. If the self test does not work, contact your dealer or a qualified service person for assistance. If the self test works properly the problem probably lies in the computer, the application software, or the interface cable. You can check the operation of your printer using the self test. Most problems you may encounter while operating your printer have simple solutions.
0 kommentar(er)
